SP10-BDxxxx60C SFP+ 10Gbps Bidi transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 10km, its electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 ohms differential. Data lines are internally AC coupled.
understand more
The SP10-CWxxLR10x SFP+ transceivers are high performance, cost effective modules supporting data rate of 10Gbps and 10km transmission distance with SMF. The transceiver consists of three sections: a uncooled DFB laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.
understand more
The SP10-CWxxER40x SFP+ transceivers are high performance, cost effective modules supporting data rate of 10Gbps and 40km transmission distance with SMF.The transceiver consists of three sections: a uncooled DFB laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.
understand more
The SP10-CWxxZR80x SFP+ transceivers are high performance, cost effective modules supporting data rate of 10Gbps and 80km transmission distance with SMF. The transceiver consists of three sections: a Cooled EML laser transmitter, a APD photodiode integrated with a transimpedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.
understand more
25G MWDM is designed for Open-WDM/MWDM 5G fronthaul solution. It uses MWDM laser and PIN receiver, transmisstion distance up to 10km, supports -40~85℃ industrial temperature. This product features with pilot tone, which enable remote monitoring of modules operation, adminitraton and matainence.
understand more
Photonics Valley’s SP10-RJ4530M SFP+ Copper-T 10Gbps transceiver is based on the SFP Multi Source Agreement (MSA). They are compatible with the 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3. SFP+-10GBASE-T uses the SFP's RX LOS (must be pulled up on host) pin for link indication. If pull up or open SFP's TX_DISABLE pin, PHY IC be reset.
understand more
The SP28-MM850SRx is SFP28 module for duplex optical data communications support 25.78 Gb/s and 28.05 Gb/s data links. It is with the SFP+ 20-pin connector to allow hot plug capability. Digital diagnostic functions are available via an I2C. This module is designed for multi-mode fiber and operates at a nominal wavelength of 850nm.
understand more
The SP28-SM31LR10x is SFP28 module for duplex optical data communications support 25.78 Gb/s and 28.05 Gb/s data links. It is with the SFP+ 20-pin connector to allow hot plug capability. Digital diagnostic functions are available via an I2C. It has built-in dual clock and data recovery (CDR). This module is designed for single-mode fiber and operates at a ominal wavelength of 1310nm.The transmitter section uses a high performance 1310nm DFB laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated InGaAs detector pre-amplifier (IDP) mounted in an optical header and a limiting post-amplifier IC.
understand more
The Photonics Valley’s SP28-BDXXXX10X is designed for Bi-directional 25G serial optical data communications by using DFB laser transmitter and PIN receiver. It is a high performance module for 25G Ethernet and Option 10 CPRI applications which operate up to 10km. This module incorporates Photonics Valley’s proven circuit and technology to provide reliable long life, high performance, and consistent service.
understand more
